150-200 YD/HOUR ALLUVIAL GOLD, WASH AND RECOVERY PLANT

Description

150-200 YD/HOUR ALLUVIAL GOLD, WASH AND RECOVERY PLANT

(1) 84″ DIA X 40′ SKID MOUNTED TROMMEL

• 7/16″ T-1 STEEL DRUM
•  5/8″ HOLES OVER 6′ LENGTH FOR FINES RECOVERY
•  1  1/4″ HOLES OVER 4′ LENGTH FOR COARSE RECOVERY
•  WATER MANIFOLD VALVE, CONTROLLED WITH 6″ FEED AND BYPASS
• (5) 4″ INLET/OUTLET, C/W CAM LOCK AND HAMMER LOCK FITTINGS
•  10′ LONG X 3″ SPRAY BAR IN SCREENING SECTION OF DRUM
•  50% OF DRUM LENGTH WITH ANGLE IRON AND CHANNEL IRON
•  BEATER BARS FOR CLAY SEPARATION
•  15′ LONG X 30″ WIDE REAR MOUNTED DISCHARGE CONVEYOR
•  DOLLIE JACKS FOR TROMMEL SLOPE ADJUSTMENT
•  10′ X 8′ SLICK PLATE WITH WATER FLOW ADJUSTMENT FLAPS FOR DIRECTIONAL CONTROL OF WATER INTO SLUICE
•  40 HP, 575 VOLT ELECTRIC DRIVE CONTROL WITH EURODRIVE REDUCER
•  VARIABLE FREQUENCY DRIVE FOR DRUM SPEED CONTROL
•  DUAL SPROCKET CHAIN DRIVE
•  KOMATSU D65 DRUM ROTATIONAL ROLLERS
•  KOMATSU D31 ALIGNMENT ROLLER

ALL ABOVE SKID MOUNTED

(1) 18 CU/YD VARIABLE DRIVE GRIZZLY FEEDER, SKID MOUNTED

•  8′ X 14′ FEED AREA WITH 10″ SEPARATION ON GRIZZLY
•  28″ X 10′ HIGH IMPACT BED ON FEED CONVEYOR
•  15 HP 575 VOLT MOTOR WITH DODGE GEAR REDUCER
•  VARIABLE FREQUENCY DRIVE

(1) 30″ X 50′ ADJUSTABLE WASH BOX CONVEYOR

•  4′ X 8′ WASH BOX WITH SPRAY NOZZLES
• (2) 2″ SPRAY NOZZLES
•  BOIL BOX
•  20 HP NORD 575 VOLT MOTOR
•  NORD/RADICON GEAR REDUCER
•  CHAIN DRIVE
•  MOUNTED ON SINGLE AXLE CHASSIS WITH DUAL WHEELS

(6) SLUICE TROUGHS AS FOLLOWS:

• 29′ TOTAL LENGTH WITH 300 FT² OF RECOVERY AREA
• TOP RUN, (10) 24′ X 48′ VORTEX DREAM MATTS, 10′ WIDTH X 8′ LONG WITH DIVIDERS
• 2ND RUN, (10) 24′ X 48′ VORTEX DREAM MATS, 10′ WIDTH X 8′ LONG
• 3RD RUN, 10′ WIDTH X 4′ LENGTH OF HUNGARIAN RIFFLES OVER #8100 MINERS MOSS
• 4TH RUN, 10′ WIDTH X 4′ LONG OF EXPANDED METAL WITH MINERS MOSS
• 5TH RUN IS 4′ LONG TRANSITION FROM 10’–12′ WIDE SLICK PLATE WITH DIVIDERS AND WATER FLOW ADJUSTMENT FLAPS
• 6TH RUN IS 12′ WIDTH X 5′ LENGTH OF AUSTRALIAN FINE RECOVERY COMMERCIAL MATTS WITH DIVIDERS
• BOTTOM DISCHARGE PLATE
• ELECTRICALLY CONTROLLED JACKS ON EACH RUN TO CONTROL WATER SPEED AND HORIZONTAL ANGLES

“ALL SKID MOUNTED WITH LIFTING EYES”

(1) 8′ X 20′ EXPLOSION PROOF PUMP SHACK (CONTAINER) ON SKIDS, WITH:

• (1) AURORA 8″ X 6″ CENT. FIRE PUMP WITH 75 HP, 575 VOLT MOTOR, 1000 GPM HIGH LIFT
• (1) ARMSTRONG 6″ X 6″ CENT. FIRE PUMP WITH 30 HP, 575 VOLT MOTOR, 500 GPM HIGH LIFT
• STEEL INTAKE AND DISCHARGE PIPING
• SHELVING AND WORK BENCH

(1) 150 KW JOHN DEERE 6 CYLINDER DIESEL GEN SET WITH:

• SUFFICIENT SWITCH GEAR AND STARTERS TO RUN PLANT
• 575 VOLT AND 208 TRANSFORMER
• 500 LITRE FUEL TANK

ALL MOUNTED IN 8′ X 18′ SKID MOUNTED SHACK

(1) 26″ W X 50′ STACKING CONVEYOR ON SINGLE AXLE CARRIER

• – RAISE AND LOWER OPTION
• – 7 1/2 HP, 575 VOLT MOTOR